解決排氣不暢的辦法

Solutions to unobstructed exhaust

由于水套芯壁薄，形狀為圓弧形，芯盒內腔開設不了大的排氣塞，而設置的Φ6排氣塞排氣效不好，易被堵塞，砂芯常因疏松或射不滿芯腔而報廢。如開設排氣槽排氣，一方面會產生跑砂現象，一方面是局部位置需開設排氣的地方排氣孔道無法引出芯盒外。而一直未解決排氣不暢的問題，每次生產時廢品都極高。經過一段時間對各種排氣方式的比較后。我想到了一種方法，既可解決排氣不暢問題又能防止跑砂現象。

Because the core wall of the water jacket is thin and the shape is circular, there is no large exhaust plug inside the core box, and the set of the 6 exhaust plug has bad exhaust effect and is easily blocked. The sand core is often scrapped because of loosening or shooting the core cavity. If the exhaust tank is opened, on the one hand, the phenomenon of sand running will be produced. On the one hand, the local exhaust duct that needs to be set up in the local position can not lead to the core box. But the problem of unsolved exhaust has not been solved, and the waste products are very high in each production. After a period of time, a variety of exhaust modes are compared. I think of a method that can not only solve the problem of exhausting exhaust but also prevent sand running.

方法是將排氣槽和排氣塞兩種排氣方法結合起來使用，如圖C，在芯盒分槽面需要開設排氣槽的地方開設排氣槽。但排氣槽不直接通出芯盒外，而是在排氣槽內再開設排氣塞。將進入排氣槽內的氣流通過排氣塞或排氣孔排出芯腔外。這樣砂氣流進入排氣槽內后，在排氣塞的作用下，氣體排掉，砂粒留下，和芯腔及槽形成一個緊實的砂芯。

The method is to combine the exhaust Gute and the exhaust plug with two kinds of exhaust methods. As in figure C, the exhaust trough is opened in the place where the slot surface of the core box needs to be opened. But the exhaust tank is not directly out of the core box, but instead of opening the exhaust plug in the exhaust tank. The air flow into the exhaust tank is discharged out of the core cavity through the exhaust plug or the exhaust hole. As the sand flow enters the exhaust tank, the gas is discharged, the sand is left, and the core cavity and slot form a tight sand core under the action of the exhaust plug.

采用此方法的優點是

The advantage of this approach is

1可解排氣槽在使用中易磨損產生噴砂的現象；

1 the phenomenon of sand blasting is easily worn out in the use of the solvable vent.

2可解決砂芯因結構形狀等原因，無法開設排氣塞或排氣槽的問題；

2 can solve the problem that the sand core can not open the exhaust plug or the exhaust slot because of the structure and shape of the sand core.

3由于排氣系統開設在分模面上，便于觀察排氣是否暢通。能及時發現是否有堵塞，預防廢品的產生，且清理方便。

3 because the exhaust system is opened on the parting surface, it is convenient to observe the expedite of the exhaust. It can be timely found whether there are clogging, prevent the production of waste, and easy to clean up.