造型機模具
Molding machine mould
1)高壓造型線：利用高壓(大于0.7Mh)壓實造型生產線。高壓造型生產率高，所得鑄件尺寸精度高和表面質量較好。同時，自于砂型緊實度高，強度大，砂型受振動或沖擊而塌落的危險小。
1) High pressure molding line: using high pressure (greater than 0.7Mh ）Compaction molding production line. High pressure molding has high productivity, high dimensional accuracy and good surface quality. At the same time, due to the high compactness and strength of sand mold, the risk of sand mold collapse caused by vibration or impact is small.
2)射壓造型線：射壓造型就是利用壓縮空氣將型砂以很高的速度射人砂箱而得到緊實。射壓造型具有很多優點：緊實度分布均勻、工作無振動、無噪、緊實速度快、機器結構比較簡單等。其又分為水平分型造型線和垂直分型造型線兩種。
2） Injection molding line: injection molding is to use compressed air to inject molding sand into the sandbox at a high speed to get compact. Injection molding has many advantages: uniform compactness distribution, no vibration, no noise, fast compaction speed, simple machine structure, etc. It can be divided into horizontal parting line and vertical parting line.
3)氣沖造型線：氣沖造型就是利用具有一定壓力的氣體瞬時膨脹釋放出來的沖擊被作用在型砂上使其緊實，克服了粘土膜引起的阻力，提高了型砂的流動性。其砂型特點是緊實度均勻且分布臺理，靠模樣處的緊實度高于鑄型背面。
3) Air impact molding line: air impact molding is to use the impact released by the instantaneous expansion of gas with a certain pressure to act on the molding sand to make it compact, overcome the resistance caused by clay film, and improve the fluidity of molding sand. The sand mold is characterized by uniform compactness and distributed bedding, and the compactness near the pattern is higher than that on the back of the mold.
4)靜壓造型線：靜壓造型就是在砂箱內填砂，對型砂施以壓縮空氣進行氣流加壓，用壓實板在型砂上部壓實，使其上下緊實度均勻。這種方法要求模板排氣好，砂箱與模板密封好。其特點是鑄件尺寸標準，生產率高。
4) Static pressure molding line: static pressure molding is to fill sand in the sand box, apply compressed air to the molding sand for air pressure, and use the compaction plate to compact the upper part of the molding sand to make its upper and lower compactness uniform. This method requires good exhaust of formwork and sealing of sand box and formwork. It is characterized by standard casting size and high productivity.