射芯機除射砂外、其余動作均采用液壓驅動。不僅提供了足夠的頂模力，保證射砂時不會產生工作臺下沉等現象；同時開模、合模、工作臺或射筒的移動、起芯等動作定位準確、運行平穩可靠；而且起芯動作更平穩有力，保證砂芯不易散列。

In addition to shooting sand, the core ejection machine adopts hydraulic drive. Not only does it provide enough die force to ensure that the work table will not sink in the sand shooting, and the movement of the die, the working table or the barrel, the movement of the core, the movement of the core and so on is accurate and stable and reliable, and the movement of the core is more stable and powerful, and the sand core is not easy to hash.

綜上就射芯機而言具有砂芯好、尺寸精確，生產率高，工作可靠，勞動強度低、清潔、安全等優點。

In a word, the core shooter has the advantages of good core, accurate size, high productivity, reliable work, low labor intensity, cleanliness, safety and so on.

1、射芯機使用時要認真觀察運轉情況，在操作中應經常用空氣吹凈潤滑部位和運轉部位的砂粒，嚴禁各潤滑部位粘砂。

1, when the core machine is used, the operation should be carefully observed. In the operation, the sand particles of the lubricating parts and running parts should be purge with the air, and the sand is strictly forbidden in all the parts of the lubrication.

2、射芯機使用時，開閉手柄氣閥時動作要平穩。

2. When the core machine is used, the movement of the valve must be steady when opening and closing the handle.

3、嚴禁開空車，必須在有載荷的情況下進行試車，檢查各工作狀態是否正常，對應該加油的地方進行加油潤滑。試車正常后方可進行工作。

3. It is strictly forbidden to drive an empty car. It must be tested under the condition of load to check whether the working state is normal or not and to lubricate the place where the oil should be refueled. The test car can work in the normal rear.

4、射芯機使用完畢后，要將手柄回到零（空）位，關閉各閥門，清掃設備，打掃現場，要保持設備各滑動（轉動）部位的清潔和潤滑，認真收檢工具，模具。

4, after the core machine is used, it is necessary to return the handle to the zero (empty) position, close the valves, clean the equipment, clean the scene, keep the cleaning and lubrication of the sliding (rotating) parts of the equipment, and carefully collect and check the tools and moulds.